The search for the best aftermarket suspension kits for 1979 Trans Am typically starts the same way: you crawl underneath, squeeze a control arm bushing, and watch it disintegrate. These cars are more than 45 years old. The original rubber suspension components were engineered to outlast the warranty period, not four-plus decades of heat cycles, road salt, and accumulated miles. The good news is that the second-gen F-body platform, which underpins every 1970 through 1981 Firebird and Trans Am, is well-supported by the aftermarket. Real choices exist at every price point, from a 100-dollar bushing kit to a full coilover conversion.

This guide covers those choices honestly, starting with the foundation and working up to the most committed builds.

Understanding the 1979 Trans Am Suspension Baseline

The 1979 Trans Am used a short-long arm (SLA) independent front suspension with coil springs and a front stabilizer bar. The rear ran a live axle on multi-leaf springs, which was conventional for performance cars of the era and responds predictably to modern upgrades.

Pontiac offered the WS6 Special Performance Package as a factory option on 1979 Trans Ams. WS6 added a larger-diameter front sway bar, a rear stabilizer bar, and revised spring rates compared to the base suspension setup. If your car has WS6 documentation or the tell-tale rear sway bar brackets, you are starting from a better baseline than a standard-suspension car. Check the trim tag and the door sticker before purchasing any sway bar upgrade, since you may already have the larger-diameter hardware installed.

By modern standards, even a WS6 car needs attention after this many years. Rubber bushings crack and compress, ball joints wear, and original shocks lose their damping capacity. A complete suspension kit should address all three areas.

Bushing Kits: The Most Cost-Effective Starting Point

No matter which direction you take the suspension, fresh bushings are the foundation. The factory rubber units degrade predictably over time, producing vague steering, excessive body roll, and a car that never feels fully planted. Polyurethane bushing kits from Energy Suspension and Prothane both cover the second-gen F-body platform. A complete set replaces every front and rear suspension bushing, the sway bar end links, and the control arm pivot points.

Polyurethane is stiffer than rubber by design. That stiffness tightens the suspension response noticeably, but it also transmits more road noise and vibration into the cabin. For a street car that sees occasional spirited driving, that trade-off is acceptable. For a daily driver, it can get tiresome. Grease the poly bushings at installation and re-grease them at regular service intervals. Squeaking from dry polyurethane bushings is a common complaint and entirely preventable.

For owners keeping the car close to stock spec, reproduction rubber bushings are the other option. Classic Industries carries suspension restoration parts for the second-gen Firebird and Trans Am platform that allow you to return the car to factory geometry without the ride change that polyurethane introduces.

Classic Industries Recommendation
Second-Gen Firebird Suspension Restoration Parts
Reproduction rubber bushings, control arm kits, and front-end hardware for 1970-1981 Firebird and Trans Am
View Details →(affiliate link. We may earn a commission at no cost to you)

Sport Spring and Sway Bar Packages

Once the bushings are sorted, springs and sway bars are where you shape the handling character of the car. Hotchkis Performance produces sport spring and sway bar kits specifically for the second-gen F-body. Their sport springs lower ride height modestly while increasing spring rate, and their front and rear sway bar kits are available in multiple diameters to suit street or track priorities. The Hotchkis Total Vehicle Suspension (TVS) package combines springs and sway bars into a single purchase and is a logical choice if you are upgrading both at once. Hotchkis publishes application-specific fitment data on their website so you can confirm compatibility before you order.

A critical note on ride height: lowering the front of an SLA-equipped car changes camber and caster. Any spring or coilover upgrade that drops the front more than about an inch should be followed by a four-wheel alignment from a shop with enough adjustment range to correct the geometry. Skipping the alignment after lowering will accelerate front tire wear and produce handling that is worse than stock.

For the rear, stiffer leaf spring packs or add-a-leaf kits increase the rear spring rate without converting to a coil spring setup. Upgrade leaf packs are available from several suppliers and suit hard launches or occasional towing better than the standard spring rates, though they firm up the daily ride noticeably.

Coilover Conversion Kits

The front suspension on the 1979 Trans Am uses a coil spring and a separate shock absorber, which makes a front coilover conversion practical without frame modification. QA1 produces front coilover kits designed to fit within the existing spring pockets on the second-gen F-body. Their single-adjustable and double-adjustable versions allow independent control of ride height and damping force, which is the right tool for autocross or road course work. QA1 lists second-gen F-body applications with specific spring rate options on their product pages.

The main limitation of a front coilover conversion is cost. A quality double-adjustable kit is a meaningful investment, and you still have the rear leaf springs to address separately. For most street cars, sport springs and sway bars will deliver most of the handling improvement at a fraction of the cost. Coilovers make sense when you need precise corner-weight adjustment or plan to run the car at timed events.

Control Arm and Front Subframe Upgrades

The control arm geometry on the second-gen F-body was designed around the tire sizes and performance expectations of the early 1970s. Running significantly wider tires or lowering the car beyond the stock range pushes the factory geometry toward its limits. Global West Suspension and UMI Performance both produce replacement lower control arms for the second-gen F-body with improved geometry and more durable bushing options, including versions with Del-A-Lum or spherical bearings in place of rubber or polyurethane.

Spherical bearing control arms eliminate bushing compliance entirely and are best suited for competition use. On the street, they transmit every road imperfection directly into the chassis. If the car never sees competition, polyurethane-bushed aftermarket control arms from UMI hit a sensible balance between precision and daily livability.

For owners working in restoration territory rather than performance upgrades, Eckler's carries OEM-equivalent control arm hardware and front-end components for the 1970-1981 platform.

Eckler's Recommendation
Classic Firebird Suspension and Front-End Parts
Control arms, ball joints, and front suspension hardware for the 1970-1981 Firebird and Trans Am
View Details →(affiliate link. We may earn a commission at no cost to you)

Matching the Kit to Your Build Goals

Street cruiser: Polyurethane bushing kit, Hotchkis sport springs, Hotchkis front and rear sway bars, fresh KYB or Monroe shocks. Four-wheel alignment afterward.

Weekend autocross or canyon car: Add UMI or Global West lower control arms, move up to QA1 single-adjustable coilovers up front, and address the rear with a stiffer leaf spring pack.

Concours or numbers-matching restoration: Reproduction rubber bushings, OEM-specification springs, and factory-equivalent shocks. Classic Industries and Eckler's both stock these parts.

Drag car: Soft front springs for weight transfer, stiff rear leaf springs, and minimal front sway bar. Front handling geometry matters far less when the car travels in a straight line.

Frequently Asked Questions

What suspension parts wear out first on a 1979 Trans Am?
Control arm bushings and sway bar end link bushings are the most common failure points. After 45-plus years, nearly every car with original rubber components needs fresh bushings. Ball joints and tie rod ends are the next items to inspect and typically require replacement at the same service interval.
Did the 1979 Trans Am come with any performance suspension from the factory?
Yes. The optional WS6 Special Performance Package added a larger-diameter front sway bar, a rear stabilizer bar, and revised spring rates. WS6 was a separate RPO code that cost extra and was not installed on every 1979 Trans Am. Verify via the trim tag before assuming your car has the upgraded hardware.
Will a coilover kit bolt into the 1979 Trans Am front suspension without cutting?
Front coilover conversion kits from companies like QA1 are designed to fit within the existing spring pockets on the second-gen F-body without frame modification. They do require a thorough alignment afterward, particularly if the kit changes ride height from the stock measurement.
Can I mix brands, such as Hotchkis springs with QA1 shocks?
Generally yes, but match the spring rate to the shock's damping range. A spring that is too stiff for the shock's valving produces a bouncy, uncontrolled ride. When combining brands, consult the shock manufacturer's recommended spring rate range before finalizing your combination, or buy a matched set from one manufacturer.
Does upgrading the rear leaf springs require any frame modification?
No. The second-gen F-body rear leaf spring mounts are conventional shackle-style attachment points. Replacement leaf packs drop in with standard hand tools. Shackle length affects both ride height and pinion angle, so measure your existing shackles before ordering a replacement pack to avoid driveline vibration issues.
Is the front suspension geometry on the 1979 Trans Am the same as earlier second-gen cars?
The basic SLA architecture carried through the entire 1970-1981 second-generation run, but Pontiac made incremental changes to spring rates, sway bar sizing, and shock valving across model years. Most aftermarket kit manufacturers list their products by body generation rather than specific year, so confirm the application notes explicitly cover 1979 before purchasing.